Category Archives: Certifications

No comments

Pneumercator Technical Certification Training Webinar Invitation

  By BlogAdmin December 1, 2021 , , , ,

2-Day Online Technical Certification Training

When:  December 7-8, 2021 (2-day online course)
Time:  9AM to 4:30PM Eastern (8AM to 3:30PM Central, 7AM to 2:30PM Mountain, 6AM to 1:30PM Pacific)

Cost: $200.00 per technician. DO NOT EMAIL CREDIT CARD INFO.

To Register: Call 1.631.293.8450 or email training@pneumercator.com.  DO NOT EMAIL CREDIT CARD INFO.

NOTE: You will be provided with the webinar link once you have registered. Certification is valid for 2 years

Pneumercator TMS4000Course Overview: This class offers technicians the opportunity to obtain or renew factory certification necessary to perform installation, startup, repair, and maintenance of the select Pneumercator products listed below.


Recommended Experience/Education: All attendees should have some prior experience with the installation and
maintenance of electronic tank gauging and leak detection systems, including general knowledge of NEC/NFPA electrical code requirements, and more specifically, hazardous location classified installation and wiring requirements and safety procedures.
Pneumercator TMS2000

Required Materials: A computer with internet access. Webcam optional. Dial up voice support provided via telephone number upon signing into webinar. Groups may share a computer but a larger screen (i.e. projector, large TV, etc.) is recommended.

Materials Provided:
• Training Presentation via internet link.
• TMS Communicator via internet link.
Certification: Renewal required every 2 years.

Pneumercator LC1000AProducts Covered:

  • LC1000-A Series Non-Discriminating Leak and/or Pt. Level Sensing system.
  • LC2000 Series Discriminating/Non- Discriminating Leak/Pt. Level Sensing system.
  • PC1000 Series pump controller.
  • TMS Series Automatic Tank Management Systems.
      • TMS3000: Multi-Tank Gauging System, 12 Tanks and 40 Leak/Pt. Level Sensors.
      • TMS2000: Two Tank Gauging System, 8 Leak/Pt. Level Sensors.
      • TMS2000W (Wireless): Multi-Tank Gauging System, 12 Tanks and 40 Leak/Pt. Level Sensors.
      • TMS1000: Single-Tank Gauging System, Non-Hazardous Applications, 4 Leak/Pt. Level Sensors.
      • TMS2000A1x: 4-20 mA Input Tank Gauging System, 4 Tanks and 4 Leak/Pt. Level Sensors.

    Pneumercator Probe

    • TMS2000A2x: Resistive Input Tank Gauging System, 4 Tanks and 4 Leak/Pt. Level Sensors.
    • TMS4000: Multi-Tank Gauging System w/Touch Screen, 48 Tanks and 48 Leak/Pt. Level Sensors.
    • TMS4000W (Wireless): Multi-Tank Gauging Sys. w/Touch Screen, 32 Tanks and 128 Leak/Pt. Level Sensors. 
  • Magnetostrictive Probes
  • Sensors
    • Point Level Sensors
      • LS600 Series (includes LS600, LS600W, LS600M, LS600F4, and LS600X)
    • Leak Sensors
      • LS600LD
      • LS610
      • RSU800
      • Pneumercator ES825 SensorES825 (Non-Discriminating and Discriminating)
      • HS100ND
      • HS100D
    • Line Leak Sensors
      • LLP203
  • TMS Communicator
    • TMSComm
    • Autopolling
    • TMS Network Configuration
  • Special Applications using flexible probes: Bulk Storage, Low Ceiling clearance, Chemicals.

See the Pneumercator Technical Certification Training Class Invitation here.

Looking for Pneumercator systems and parts? Pneumercator Liquid Level Control SystemsCheck out our web store!

And if you can’t find what you are looking for, please call us at 1.800.238.1225 or Email Us with any further questions or to place an order!

The John W. Kennedy Company appreciates your business and continued support!

JWK USA Logo

No comments

Omntec Proteus FREE Web-based Training Course

  By BlogAdmin November 23, 2021 , , , , , ,

Omntec Proteus ATG

JOIN OMNTEC FOR ONLINE ASC TRAINING ON 12/13/21 @ 11 AM EST

OMNTEC’s FREE ASC training is a web-based course including an exam that can be completed at your own pace. The training presentation is live and hosted through Zoom. The course is roughly 2.5 hours long.

Once you register for December’s session, you will receive an email with links to documents you can reference during the training session and the certification.

The Zoom meeting link will be sent out the Friday before the training session. Upon completion of both the training and exam, you will be provided a certificate and a wallet card that will be emailed directly to you.

REGISTER HERE

Omntec Proteus ATG

Omntec logo
You can find Omntec products in our web store		 John W Kennedy Company | Omntec SBI
Use our Proteus Shop By Image feature

The John W. Kennedy Company appreciates your business and continued support!

JWK USA Logo

2 Comments

Franklin Fueling Systems EVO™ 600 and EVO™ 6000 ATGs FREE ONLINE TRAINING!!

  By BlogAdmin April 2, 2021 , , , , ,

GET CERTIFIED ON THE LATEST ​​​AUTOMATIC TANK GAUGE TECHNOLOGY

For a limited time, we are offering FREE FFS PRO® University online certification for EVO™ 600 and EVO™ 6000 Automatic Tank Gauge Installation / Wiring and Programming.

This free online training is available now through June 30, 2021!!

Franklin Fueling Systems Fueling System Safety A few things to know before you get started on the free training. 

You are required to have an FFSPRO account. If you do not have one, you can register here.

Next, you will be required to take the online Fueling System Safety course. Be aware that if you are not using one of the following browsers, you may encounter functionality and content issues:
⇒ Internet Explorer 9 or later
⇒ Safari 5.1 or later
⇒ Google Chrome 17 or later

Controller Specialist: EVO™ 600 & EVO™ 6000 Installation & Wiring

Controller Specialist: EVO™ 600 & EVO™ 6000 Installation & Wiring EVO™ 600 and EVO™ 6000 automatic tank gauge model overview, installation and wiring of modules, probes, remote alarms, sensors, and Turbine Pump Interface

Begin Presentation          (Login to Take Test!)

 PREREQUISITES:
Fueling System Safety

Site Startup Specialist: EVO™ 600 & EVO™ 6000 Programming

Site Startup Specialist: EVO™ 600 & EVO™ 6000 Programming EVO™ 600 and EVO™ 6000 fuel management & system programming including user/network interfacing, console navigation, initial setup, and optional supported feature programming.

Begin Presentation       (Login to Take Test!)

 PREREQUISITES:
Fueling System Safety

EVO™ 600 & EVO EVO™ 6000

The new EVO™ 600 and EVO™ 6000 ATGs provide highly accurate inventory management and full-featured compliance monitoring for any size fuel system. Advanced features include Corrosion Control™ System automation and monitoring, Electronic Line Leak Detection, and DEF/AdBlue® recirculation.

Be sure to check out our ever-expanding product offerings and great deals from Franklin Fueling’s many brands found in our webstore.

EVO 600 Base Model
EVO 600 Base Model		 EVO 6000 Base Model
EVO 6000 Base Model
FFS APT FFS CableTight FFS EBW
FFS EVO FFS FE Petro FFS Flex-Ing
FFS Healy FFS Incon FFS UPP

The John W. Kennedy Company appreciates your business and continued support!

JWK USA Logo

No comments

OPW NEW ENGLAND UST EVR Certification Course – Live Class

  By BlogAdmin March 13, 2020 , , , ,

OPW New England UST EVR Certification Class


The OPW UST EVR live certification course provides attendees a hand’s on opportunity to install and service all of the OPW UST EVR Phase One System Components listed on the California Air Resources Board (CARB) Executive Order. Attendees will use the tools provided in class while performing basic installation and routine maintenance of phase one components. There is no experience necessary and the class is free. There will be a test at the conclusion of the class and with a passing grade you will receive a 2 year certification.

 

There are 2 training session dates open to all OPW distributors, contractors and end users.

WHEN: 8:30 AM Eastern Standard Time
Tuesday, April 21, 2020
(4 hour session)		 OPW Loop SystemOPW UST
WHERE: DoubleTree by Hilton
5400 Computer Drive
Westborough, MA 01581
(508) 366-5511
WHEN: 8:30 AM Eastern Standard Time
Wednesday, April 22, 2020
(4 hour session)
WHERE: Hilton Garden Inn
800 Hall of Fame Ave
Springfield, MA 01105
(413) 886-8000
EACH CLASS SIZE: 20 attendees maximum
(first come first serve basis)
MEAL: Coffee, Juice, Bagels
PRESENTER: Glenn “Whitey” Eckart
HOSTED BY: Tim Andersen
OPW District Manager
tim.andersen@opwglobal.com
REQUIREMENTS: IMPORTANT:
Please respond ASAP !!
You will be required to provide each attendee’s name, company name and email address to officially register any attendee for the training class

Enrollment will be on a first come first serve basis.

If registration is low there is a possibility that training sessions may be cancelled.

To reserve your spot today, contact us at 1.800.451.4021 or reserve your spot(s) directly with Tim Anderson by contacting him at tim.andersen@opwglobal.com.

 

The John W. Kennedy Company appreciates your business and continued support!

 

JWK USA Logo

No comments

OPW NEW ENGLAND UST EVR Certification Course – Live Class

  By BlogAdmin August 13, 2019 , , ,

OPW New England UST EVR Certification Class


The OPW UST EVR live certification course provides attendees a hand’s on opportunity to install and service all of the OPW UST EVR Phase One System Components listed on the California Air Resources Board (CARB) Executive Order. Attendees will use the tools provided in class while performing basic installation and routine maintenance of phase one components. There is no experience necessary and the class is free. There will be a test at the conclusion of the class and with a passing grade you will receive a 2 year certification.

 

There are 2 training session dates open to all OPW distributors, contractors and end users.

WHEN: 8:30 AM Eastern Standard Time
Tuesday, September 10, 2019
(4 hour session)		 OPW Loop SystemOPW UST
WHERE: Hilton Garden Inn
800 Hall of Fame Ave
 Springfield, MA 01105
(413) 886-8000
WHEN: 8:30 AM Eastern Standard Time
Tuesday, September 11, 2019
(4 hour session)
WHERE: Hampton Inn
449 Page St
Stoughton, MA 02072
(781) 297-2900
EACH CLASS SIZE: 20 attendees maximum
(first come first serve basis)
MEAL: Coffee, Juice, Bagels
PRESENTER: Glenn “Whitey” Eckart
HOSTED BY: Tim Andersen
OPW District Manager
tim.andersen@opwglobal.com
REQUIREMENTS: IMPORTANT:
Please respond ASAP !!
You will be required to provide each attendee’s name, company name and email address to officially register any attendee for the training class

Enrollment will be on a first come first serve basis.

If registration is low there is a possibility that training sessions may be cancelled.

To reserve your spot today, contact us at 1.800.451.4021 or reserve your spot(s) directly with Tim Anderson by contacting him at tim.andersen@opwglobal.com.

 

The John W. Kennedy Company appreciates your business and continued support!

 

JWK USA Logo

No comments

OPW NEW ENGLAND UST EVR Certification Course – Live Class

  By BlogAdmin June 5, 2019 , , ,

OPW New England UST EVR Certification Class


The OPW UST EVR live certification course provides attendees a hand’s on opportunity to install and service all of the OPW UST EVR Phase One System Components listed on the California Air Resources Board (CARB) Executive Order. Attendees will use the tools provided in class while performing basic installation and routine maintenance of phase one components. There is no experience necessary and the class is free. There will be a test at the conclusion of the class and with a passing grade you will receive a 2 year certification.

 

This training is open to all OPW distributors, contractors and end users.

WHEN:  8:30 AM Eastern Standard Time
Tuesday, June 18, 2019
(4 hour session)		 OPW Loop SystemOPW UST
WHERE: Hilton Garden Inn
800 Hall of Fame Ave
 Springfield, MA 01105
(413) 886-8000
CLASS SIZE: 20 attendees maximum
 (first come first serve basis)
MEAL: Coffee, Juice, Bagels
PRESENTER: Glenn “Whitey” Eckart
HOSTED BY: Tim Andersen
OPW District Manager
tim.andersen@opwglobal.com
REQUIREMENTS: IMPORTANT:
Please respond ASAP !!
You will be required to provide each attendee’s name, company name and email address to officially register any attendee for the training class

Enrollment will be on a first come first serve basis.

If registration is low there is a possibility that training sessions may be cancelled. 

To reserve your spot today, contact us at 1.800.451.4021 or reserve your spot(s) directly with Tim Anderson by contacting him at tim.andersen@opwglobal.com.

 

The John W. Kennedy Company appreciates your business and continued support!

 

JWK USA Logo

No comments

UPDATE: 2019 John W. Kennedy Company “Forging Relationships” Trade Show Registrations Now Open!!

  By BlogAdmin January 15, 2019 , ,

Crowne Plaza Warwick RI

Once again, it is time for the John W. Kennedy Company’s biennial trade show at the:2015 JWK Trade Show 85 Years

JWK Basic Training Trade Show

Crowne Plaza Hotel Warwick
801 Greenwich Ave
Warwick, RI  02886
401.732.6000

 

 

 

CLICK HERE TO REGISTER NOW!

 

As always, the show features dozens and dozens of vendors showing their latest and greatest products, services, installation and maintenance tips.

The first day is chock full of training and certification seminars, followed by an open bar, cocktail and hors d’oevres reception at 4PM with the gypsy-jazz stylings of the Bianco Martinis.

 

 

 

FORGING RELATIONSHIPS
Trade Show Training & Certification Seminar Schedule

Wednesday, March 27, 2019
Seminars fill quickly – CLICK HERE REGISTER NOW to guarantee your spot!

Seminar Description Time
OPW Flexworks
Underground Piping Re-certification
8 – 9AM
FFS APT
Underground Piping Re-certification
9:15 – 10:15AM
Icon Containment
Repair Boot Installation Certification
10:30 – 11:30AM
Containment Solutions
UST Installation Certification
11:45AM – 1:30PM
Gilbarco Veeder-Root
EMV Timeline & Deadlines – what you need to do!
2 – 3PM

As always, this is a FREE event – watch our website and blog for upcoming show registration announcements!

CLICK HERE TO REGISTER NOW!

The John W. Kennedy Company appreciates your business and continued support!
JWK USA Logo

No comments

URGENT: ALL current GVR Safety Certifications will expire December 31, 2018 – Take Action Now To Stay Certified!!

  By BlogAdmin December 4, 2018 , , , ,

JWK Technical Training ClassesURGENT: ALL current GVR Safety Certifications will expire December 31, 2018, regardless of when the certification was taken!!

As of January 1, 2019, technicians will be required to have the API Safety Certification in the USA and the POST Safety Certification in Canada.

 

You can read the updated Gilbarco / Veeder-Root Pathway to Certification Sequence document here to learn about the latest changes to the GVR requirements.

You can also see the updated API/POST document here that includes link to the:
USA Safety Requirement API WorkSafe site: https://worksafe.api.org/DesktopDefault.aspx
Canada Safety Requirement POST Training site: https://learn.posttraining.ca/login/index.php

View our updated our 2019 Tech Training Class Schedule here.

Download the updated 2019 JWK Tech Training Enrollment form here.

 

If you have any further questions or concerns, you can contact Chris Bedard, our GVR Certified Trainer at ceb@jwkemail.com or call Chris at 1.855-978-6737.

The John W. Kennedy Company appreciates your business and continued support!

JWK USA Logo

No comments

OPW New England UST EVR Certification Class – Official Invitation ( December 12, 2018 )

  By BlogAdmin November 5, 2018 , , , , ,

JWK USA Logo

OPW UST EVR Training Certification

OPW invites you to attend their UST EVR Training Certification class.

Description: The OPW EVR live certification course provides attendees a hand’s on opportunity to install and service all of the OPW UST EVR Phase One System Components listed on the California Air Resources Board (CARB) Executive Order. Attendees will use the tools provided in class while performing basic installation and routine maintenance of phase one components. There is no experience necessary and the class is free. There will be an open book test at the conclusion of the class and with a passing grade you will receive a 2 year certification.

When: Wednesday, December 12, 2018

Where: Hilton Garden Inn  – 800 Hall of Fame Ave. – Springfield, MA 01105

 

IMPORTANT:  Please contact us at 1.800.451.4021 or email us here ASAP to reserve a spot with the attendee name, company name & email address. Please note: all (3) bits of information are needed in order to officially register the attendee for the training class.

Enrollment will be on a first come first serve basis. If registration is low there is a possibility that training sessions may be cancelled.

 

The John W. Kennedy Company appreciates your business and continued support!

JWK USA Logo

No comments

FFSPRO Tech Update – Free Online EVO Training & FMP-LL3 Digital Probe Backward Compatibility

  By BlogAdmin March 23, 2018 , , , ,

FMP-LL3 Digital ProbesThe Campus Tech UpdateFMP Digital Probe Wiring Options

Franklin Fueling System has one of the best online resources for documentation, videos and online training.

FMP-LL3 DIGITAL PROBE BACKWARDS COMPATIBILITY

Did you know Franklin Fueling Systems’ new FMP-LL3 Series probes are backwards compatible with most of their existing ATGs? If you did, you are pretty well informed and must be utilizing those online resources Franklin Fueling has to offer already.  If not, head on over to The Campus for details on the proper wiring methods and learn more by clicking here!

 

FREE ONLINE EVO™ 200/400 TRAINING

As the saying goes, “If it’s for free, it’s for me!”  That means you should really check out Franklin Fueling Systems’ new EVO™ 200 and EVO™ 400 automatic tank gauge model training in wiring, installation and programming. Learn more by clicking here!

Be sure to explore both of the above links provided to see what other technical offerings Franklin has to offer.  Great resources to have on hand when you have questions in the field.

The John W. Kennedy Company appreciates your business and continued support!

JWK USA Logo