Check Out The Latest Financing Programs From Patriot Capital!
Exclusive Gasboy Prime Program
Get great rates and low payments!
Now through September 30, 2022, Patriot Capital is offering an exclusive financing program for Gasboy Islander Prime and Atlas Prime equipment.
Benefits of financing with Patriot Capital include:
100% Project Financing
Deferred Payment Plan
Fixed Payments, Competitive Rates
Upgrade Multiple Sites At Once
All packages include EKOS and the fuel site module. Click here to see brochure for details and feel free to contact us today at 1.800.451.4021 oremail us for more details.
Bundle Financing Program
Use Promo Code PC2022
Now through September 30, 2022, Patriot Capital is offering a bundle financing program for select Veeder Root ATG, HydrX and Red Jacket equipment.
Eligible Products
The TLS-450PLUS and TLS4 Series Automatic Tank Gauges (ATGs) with available factory installed options, and probes and sensor product necessary for compliant installation except as listed below
HydrX Fuel Conditioning System
Red Jacket Submersible Turbine Pumps (STPs), including The Red Jacket, The Red Jacket AG, Red Armor®, Maxxum®, and CoreDEF™
Ineligible Products
TLS-350 Series ATGs, parts, and accessories
Mag Flex Tall Tank Probes and accessories
Carbon Canisters
Spare or replacement parts
Installation, shipping, and other costs are not included in the equipment financing program
Financing Options
Get 3.9% for 60 months on ATGs or HydrX financed alone.
Get 2.9% for up to 60 months when bundling ATGs and HydrX.
Get 1.9% for up to 60 months when bundling ATGs, HydrX and Red Jacket STPs.
For any questions on this financing program, contact us at 1.800.451.4021 or email us
Veeder-Root has specific requirements for all Automatic Tank Gauge (ATG), probe, sensor and Pressurized Line Leak Detection (PLLD) transducer wiring – this is to maintain intrinsic safety as well as reduce electrical noise interference. This notification will provide a brief introduction into Veeder-Root’s probe and sensor wiring requirements. This should be used in conjunction with local, state and federal electrical codes.
Basic Wiring & Installation Requirements
The following are Veeder-Root’s field wiring requirements:
All probes and sensors must use two-wire shielded cable.*
Use a single continuous length of shielded cable with no splices to ensure optimum signal strength.
All shielded cable runs must be less than 1000 feet.
An epoxy pack must be used for all wiring splices in the field.
Weatherproof junction boxes are required for all conduit runs to the monitoring locations (e.g., STP sump or dispenser pan).
All shields must be grounded at the console, cut-off in the field.
When exiting the console, shielded cable must be run through rigid conduit.
Shielded cable should be rated between 14 to 18 AWG stranded copper wire and must be rated less than 100 picofarads per foot.**
All three divider plates must be left in place in-between any of the four slots in the TLS-450PLUS console or the TLS-XB Expansion Box.
The divider plates and empty slot covers cannot be modified in any way. This includes drilling holes or cutting the plates.
Note: Removing or modifying the divider plate can lead to electrical noise interference issues and violates UL/cUL and other licensing bodies.
Four-conductor or more shielded cable cannot be used with Veeder-Root probes or sensors. Two wires cannot be connected to a sensor while the other two wires are connected to another device, even if the two devices are installed in the same sump.
Confirm the console has two isolated grounds.
To test the grounds, disconnect these two cables from the console. Place the leads of the ohmmeter on each grounding wiring and confirm it reads less than 1 ohm of resistance. If it reads more than 1 ohm of resistance, then the console has bad grounding, which could be a cause of an electrical noise interference issue.
Installation Review
This example shows a clean installation.
✅ One pair of two-conductor shielded cable is used per device.
✅ All shields are grounded at the console.
✅ All shielded cable is run through a rigid conduit.
This example shows an incorrect installation.
❌ The field wiring does not meet Veeder-Root, UL/cUL and other licensing bodies’ wiring requirements. This site is using four-conductor shielded cable. (Shields are not shown). As mentioned before, two-conductor shielded cable is required for all probes and sensors.
Further Information
Please feel free to contact us with any further questions about this notification at 1-800-451-4021 or Email Us
Well look no further – click on the Veeder-Root logo below to visit our web store, where we have hundreds of the most popular Veeder-Root items ready to buy in our webstore and if you can’t find it there, please feel free to contact us at 1-800-451-4021 or Email Us !!
The John W. Kennedy Company appreciates your business and continued support!
HydrX™ Fuel Conditioning System
Site Inspection Guide Update
An updated version of the HydrX Fuel Conditioning System Site Inspection Guide (576047-355, Rev. E) is now available. See the links below. This guide will help determine if the HydrX Fuel Conditioning System can be implemented into an existing fuel management system. Review and fill out this document in order to pinpoint the HydrX part numbers required. If any issues are encountered during your site inspection, please contact us by phone at 1.800.451.4021 or email us. Your completed Site Inspection Guide should be submitted to essentials@jwkemail.com.
IMPORTANT: Only Veeder-Root HydrX Certified Technicians are authorized to install this system.
If you have not already, enroll in the web-based Veeder-Root HydrX Install and Service Course. This 1-hour course prepares Veeder-Root ATG Certified Technicians to install and service the HydrX Fuel Conditioning System. Users will become familiarized with all primary components of the HydrX system, including: the Fuel Conditioner, Water Intake Device, Guide Tube, and Fuel Conditioning Controller.
✏ Quick Links for Self-Enrollment
NOTE: You must sign up with Gilbarco Veeder-Root in order to enroll in the online training if you haven’t done so previously!
Well look no further – click on the Veeder-Root logo below to visit our web store, where we have hundreds of the most popular Veeder-Root items ready to buy in our webstore and if you can’t find it there, please contact us!
If you have any questions about HydrX or would like to receive a quote for HydrX or any other Veeder-Root system and/or parts , please feel free to contact us at 1-800-451-4021 or Email Us !!
The John W. Kennedy Company appreciates your business and continued support!
Prior to installing a HydrX Fuel Conditioning System, ensure all hardware is received and on site. Failure to install the system completely can result in diesel fuel releasing into the containment sump and creating a dangerous condition.If you feel you are missing parts or components, contact Veeder-Root Technical Support at +1.800.323.1799, before proceeding with the system installation.
IMPORTANT: Only Veeder-Root HydrX Certified Technicians are authorized to install this system.
If you have not already, enroll in the web-based Veeder-Root HydrX Install and Service Course. This 1-hour course prepares Veeder-Root ATG Certified Technicians to install and service the HydrX Fuel Conditioning System. Users will become familiarized with all primary components of the HydrX system, including: the Fuel Conditioner, Water Intake Device, Guide Tube, and Fuel Conditioning Controller.
✏ Quick Links for Self-Enrollment
NOTE: You must sign up with Gilbarco Veeder-Root in order to enroll in the online training if you haven’t done so previously!
Well look no further – click on the Veeder-Root logo below to visit our web store, where we have hundreds of the most popular Veeder-Root items ready to buy in our webstore and if you can’t find it there, please contact us!
If you have any questions about HydrX or would like to receive a quote for HydrX or any other Veeder-Root system and/or parts , please feel free to contact us at 1-800-451-4021 or Email Us !!
The John W. Kennedy Company appreciates your business and continued support!
As of March 2022, iButtons are no longer being used in consoles with software version 10.C or later. The software features will be stored directly on the CPU Boards. The CPU Boards will still have a socket for the iButton but will have a “NOT USED” decal included (see image below). IMPORTANT: The iButton is still needed for consoles with software version 10.B or prior.
✏ All TLS-450PLUS & TLS4 Series Consoles
CPU Board Replacement ✏ Software version 10.C or later will no longer use the iButton. ✏ Software version 10.B or prior will continue to use the iButton and it must be moved to the new CPU.
iButton Replacement Replacement iButtons are no longer available. ✏ TLS-450PLUS consoles with defective iButtons will require the new CPU and software version 10.C or later. ✏ TLS4 Series consoles with defective iButtons do not require replacing the CPU but must be upgraded to software version 10.C or later.
✏ Migrating a TLS-450 to a TLS-450PLUS Console
Migration kits are no longer available for purchase. Last time buy was December 31, 2021. However, if you have a migration kit, follow these steps to migrate a TLS-450 to a TLS-450PLUS console.
1. Create a backup of the TLS-450 using the thumb drive provided in the kit. 2. Install the new CPU and SD card.
IMPORTANT: Do not move iButton to the new CPU.
3. Restore the TLS-450 back-up into the TLS-450PLUS.
Note: In some circumstances, a “Media Access Error” may occur but will clear once the database restore is complete.
Well look no further – click on the Veeder-Root logo below to visit our web store, where we have hundreds of the most popular Veeder-Root items ready to buy in our webstore and if you can’t find it there, please contact us!
If you have any questions about TLS450 or would like to receive a quote for TLS450 Series or any other Veeder-Root system and/or parts , please feel free to contact us at 1-800-451-4021 or Email Us !!
The John W. Kennedy Company appreciates your business and continued support!
The TLS-450PLUS console must be installed per the TLS-450PLUS Site Prep and Installation Manual (577014-073) and the UL/cUL Control Drawing – TLS-450/8600 Consoles (331940-008). The console may not be modified in any way. This includes drilling holes, cutting the metal and plastic walls or removing the divider plates located in the module bay. Removing or modifying the divider plates can lead to the product or installation not being compliant with UL/cUL requirements. All three divider plates must be left in place in-between any of the four slots in the TLS-450PLUS console or TLS-XB Expansion Box.
IMPORTANT: Removing the divider plates can lead to electrical noise interference issues and violates UL/cUL and other licensing bodies.
Designated knockouts are the only approved wiring openings. As needed, knockouts can be removed to allow rigid conduit to be connected to the console. Any unused positions where knockouts have been removed must be properly sealed, per the latest National Electric Code.
✏ Installation Review
This example shows a clean installation. ✅ All wires exit the console and immediately enter a rigid conduit (not shown).
✅ In addition, the console has not been altered in any way; unused knock-outs have been left in place and the divider plates have not been removed (each module is physically separated with a metal plate).
This example shows an incorrect installation.
❌ The divider plate was removed between the two USM modules, in slots 2 and 3. This is against Veeder-Root’s installation requirements and violates the UL/cUL and other licensing bodies. The divider plate must remain in place and cannot be modified.
❌ All wires must be run through rigid conduit and can only be used in the module slot that the conduit is connected to.
Well look no further – click on the Veeder-Root logo below to visit our web store, where we have hundreds of the most popular Veeder-Root items ready to buy in our webstore and if you can’t find it there, please contact us!
If you have any questions about TLS450 or would like to receive a quote for TLS450 Series or any other Veeder-Root system and/or parts , please feel free to contact us at 1-800-451-4021 or Email Us !!
The John W. Kennedy Company appreciates your business and continued support!
Passport Point-of-Sale: Tips & Tricks for your POS
Looking for some quick online guidance, tips and tricks for your Passport POS? Click on the image below to get video help with instructions for cashiers, managers and self-checkout! There are also links to view and download reference cards to create a nice library to access in moments.
Looking for Gilbarco equipment? Click on the links below to visit our web store :
We are almost one month into 2022… have you made a plan to achieve your goals?
If not, here’s a refresher on what you should be doing this year:
According to a study, 64% of us will apparently abandon our New Year’s resolutions within a month, so we thought we’d share some new ideas to replace the ones you didn’t quite keep up with.
Here are some resolutions that fuel and convenience retailers need to add to their list for 2022.
NEXT-LEVEL CX
Take your customer experience to the next level this year. The modern customer experience demands a frictionless shopping experience from fill-up to checkout. Here are three ways to up your CX game:
1. Whether you need help with staffing or long lines, Passport® Express Lane™ is one of the most cost-effective solutions to optimize your operations. Committing to a self-checkout strategy is the first step in creating next-level CX. Express Lane gives everyone, including managers, employees, and customers – more flexibility.
2. Express Ordering is another smart solution that helps c-stores set themselves apart with fresh food options. By automating the ordering process, Express Ordering puts the consumer in control – driving increased loyalty and upsell opportunities.
3. Every store’s customer data needs to be secure. Passport POS and Encore® 700 S fuel dispensers come EMV-ready and PCI-certified out of the box to ensure your customers’ private information stays secure.
DEFinite ADVANTAGE
Demand for diesel exhaust fluid is rising. The percentage of DEF pumps in the overall automotive DEF supply mode increased from 14% in 2011 to 40% in 2019, according to market research firm Reportlinker.
This is due to more stringent environmental regulations and the manufacturing of new DEF-compatible vehicles that are replacing the old ones.
For retailers with Gilbarco’s Encore S fuel dispensers or later, the DEF equipment cabinet(s) can be added left or right oriented or on either side of the fueling position, allowing for even more convenience and create loyalty with your diesel customer base.
COMBAT CORROSION
Now is the perfect time to commit to quality fuel. Part of that commitment means protecting your underground storage tanks.
The Veeder-Root HydrX Fuel Conditioning System combats in-tank corrosion by providing continuous water removal within diesel underground storage tanks. The system’s unique design removes water from the lowest point in the tank, preventing water from stagnating on the tank bottom and breeding microbial contaminants. The integrated filtration removes entrained water, rust, sand, and microbial particulate from the fuel, polishing it before returning clean fuel back to the tank.
Learn how the HydrX Fuel Conditioning System prevents corrosion from eating away at the bottom line for Cumberland Farms.
LEVEL UP YOUR ATG
And finally, resolve to upgrade your automatic tank gauge to the industry’s latest, most reliable ATG equipment with the TLS-450PLUS and Central Device Management (CDM).
The TLS-450PLUS console provides an expanded, advanced feature set at a lower price point than the TLS-350 console without needing to replace your probes or sensors. It also unlocks compatibility with other solutions like HydrX.
CDM is a server-based software package to manage your entire network of sites, ensuring your ATG consoles are always up to date with the latest features and security updates.
THE BOTTOM LINE
For 2022 and beyond, focus on solutions that make your operations more frictionless, efficient, secure, and connected.
Whether it’s on the forecourt, underneath it, or in the cloud, Gilbarco Veeder-Root is the only solutions provider that covers every area of your fuel and convenience business. As your partner for what’s next, let’s see if we can help you beat the stats and keep your new year’s resolution.
If you have any questions or would like to receive a quote for any of the systems and equipment mentioned above, please contact us at 1.800.238.1225 orEmail Us.
Looking for Gilbarco or Veeder-Root equipment? Click on the links below to visit our web store :
The TLS4 Series consoles come with security features allowing for greater protection and control of access to the Automatic Tank Gauge. Features such as configurable user access and segmented network ports help ensure both network and front-panel security.
This update covers:
User and Roles Admin
Create User Accounts
Custom Roles
System Security
Front Panel Security
Serial Command Port (TCP/IP Interface)
SSH Port
Serial Command Over SSH
HTTPS Port
User Admin Via Web
Router and Network Switch
User & Roles Admin
Create User Accounts & Custom Roles
All TLS4 Series consoles come preconfigured with three roles: Administrator, Operator and Regulator. Additional custom roles can be programmed.
Menu –> System Administration –> Roles Admin
• Administrator: This role gives full access to the console – including the ability to create new roles and users.
• Operator: This role allows the user to view and generate reports and perform certain manual functions, such as starting a manual line or tank test.
• Regulator: This role allows the user to print and view console reports.
Note: Users assigned to the Regulator role cannot be deleted.
To add a Custom role, select Actions –> Add New Role
The Custom role allows each individual screen to be viewable, editable or not accessible. For example, in Setup under the Automatic Events section, each option can be customized:
Veeder-Root strongly recommends creating an Administrator account with a unique password. This will disable the default username and password.
Note: When using the Plus View or Remote View apps, the same login credentials are used.
Security
System Security
The TLS4 Series consoles have optional security features to enhance protection in addition to front panel security that requires a username and password, when enabled.
Front Panel Security: When disabled, all users can access all screens with no password required. When enabled, users must login with a password to gain access to the screens they’re allowed to view.
Serial Command Port (TCP/IP Interface): When disabled, the console will not accept any serial commands sent through a telnet session.
Note: This will not block all traffic on the TCP/IP port. It will only block serial commands.
SSH Port: When disabled, all traffic on the SSH port will be blocked.
Serial Command Over SSH: For the SSH Public Keys feature to work, this port and the SSH port must be enabled. By default, this port is disabled.
HTTPS Port (Web Access): When disabled, all traffic on the HTTPS port will be blocked. This will prevent access to the web portal, and the Plus View and Remote View apps.
User Admin via Web: When disabled, the System Administration screens will be blocked from the web portal – access to these two screens will only be available on the console’s front panel.
Router or Network Switch
Most routers or network switches have additional features allowing ports to be enabled or disabled. Contact device manufacturers or internet service providers (ISPs) for more information.
Well look no further – click on the Veeder-Root logo below to visit our web store, where we have hundreds of the most popular Veeder-Root items ready to buy in our webstore and if you can’t find it there, please contact us!
If you have any questions about TLS4 Series or would like to receive a quote for TLS4 Series or any other Veeder-Root system and/or parts , please feel free to contact us at 1-800-451-4021 or Email Us with any further questions or inquiries.
The John W. Kennedy Company appreciates your business and continued support!
Well look no further – click on the Veeder-Root logo below to visit our web store, where we have hundreds of the most popular Veeder-Root items ready to buy in our webstore and if you can’t find it there, please contact us!
If you have any questions about HydrX or would like to receive a quote for HydrX or any other Veeder-Root system and/or parts , please feel free to contact us at 1-800-451-4021 or Email Us with any further questions or inquiries.
The John W. Kennedy Company appreciates your business and continued support!